Skip to main content

Configure at same time many accounts are located on different Exchange servers in one instance of Outlook 2010

 

How to configure and run at the same time, many accounts are located on different Exchange servers in a single instance of Outlook 2010?


Yesterday I wrote about this ExtraOutlook app that does not work with Outlook 2007. That's true but it turned out that Outlook 2010 can handle in one instance multiple Exchange accounts located on different servers! Thank Mairusz for information about this new functionality. How do I do? Normally this can not be done from within Outlook. You have to close it and start the mail, which can be found in Control Panel.



To go to account settings, select the E-mail Accounts ...:
Since I already had set up the first account is enough to add new ones by clicking the New ...:
Next it's standard configuration of your Exchange account.
The result is two accounts in a single instance of Outlook:
It is true that simple? It is a pity that so long waited for this. But now it remains only to enjoy 
Something seems to me that this is for me the best "feature" of the new Outlook 2010. What is interesting in several presentations on the new Outlook, I have not seen anything about this new and desired functionality.

Comments

Post a Comment

Popular posts from this blog

Calculate how much data can be transferred in 24 hours based on link speed in data center

  In case you are planning for migration via DIA or IPVPN link and as example you have 200Mb stable speed so you could calculate using the below formula. (( 200Mb /8)x60x60x24) /1024/1024 = 2TB /per day In case you have different speed you could replace the 200Mb by any rate to calculate as example below. (( 5 00Mb /8)x60x60x24) /1024/1024 =  5.15TB  /per day So approximate each 100Mb would allow around 1TB per day.
Post a Comment
Read more

Integration with vCloud Director failing after NSXT upgrade to 4.1.2.0 certificate expired

  Issue Clarification: after upgrade from 3.1.3 to 4.1.2.0 observed certificate to be expired related to various internal services.   Issue Verification: after Upgrade from 3.1.3 to 4.1.2.0 observed certificate to be expired related to various internal services.   Root Cause Identification: >>we confirmed the issue to be related to the below KB NSX alarms indicating certificates have expired or are expiring (94898)   Root Cause Justification:   There are two main factors that can contribute to this behaviour: NSX Managers have many certificates for internal services. In version NSX 3.2.1, Cluster Boot Manager (CBM) service certificates were incorrectly given a validity period of 825 days instead of 100 years. This was corrected to 100 years in NSX 3.2.3. However any environment originally installed on NSX 3.2.1 will have the internal CBM Corfu certs expire after 825 regardless of upgrade to the fixed version or not. On NSX-T 3.2.x interna...
Post a Comment
Read more

Recreating a VMFS-3 or VMFS-5 partition table in ESXi 5.x

For this kind of issues you need to engage VMware support on this, following any part of this article could lead to more complex situation if not ran by an expert.   Symptoms Datastore does not mount because of a lost or overwritten partition table.   Purpose When a VMFS partition is created in ESX 3.x or ESX 4.x, it has a Master Boot Record (MBR) partition map. The MBR is written to the first 512 B block (LBA0) and contains the information where the (VMFS) partition starts and ends. ESXi 5.0 introduced VMFS-5, which uses a GUID partition table (GPT) for new datastores. When a VMFS-3 partition is created in ESXi 5.x and is later updated to VMFS-5, the original partition map (MBR) is maintained. If the partition information of a VMFS datastore is deleted or overwritten (for example, by a Windows system with direct access to the same disks), it is impossible to determine if the partition map was GPT or MBR. The only time you can be sure that a GPT partition map was used is if th...
Post a Comment
Read more