Skip to main content

How to renew a self signed certificate in Microsoft Exchange Server 2007

 

When a new Exchange Server 2007 role is installed on a computer the server automatically generates a self signed certificate to be used with services like transport (SMTP), POP, IIS (OWA and Exchange Web Services) and IMAP. This certificate expires right after the completion of one year from the date server was installed or the certificate was reassigned manually. To check the status of the certificate using Exchange Management Shell. Executing the cmdlet Get-ExchangeCertificate |FL displays all relevant information about all the certificates assigned, enabled and being used or not used by Exchange Services. 
You may see more than one certificate listed on your exchange server(s) and that may be simply because you or someone else from your team have already tried working with certificates on the server.
If you see the above picture, you will notice that the certificate I have on my server is valid till 24th March 2010. NotAfter holds the value in mm/dd/yyyy h:mm:ss format. NotAfter – means this certificate will not be valid after the time stamp listed in this field. On the other hand the value NotBefore – means that this certificate will not be valid before the time stamp mentioned.
So once you cross the date listed in field NotAfter the certificate becomes invalid and indeed may open up doors to many other troubles like connectivity to web services, SMTP transport, POP and IMAP retrieval, etc. To renew the certificate you can simply run a cmdlet and get a new self signed certificate. But, this is just not as simple as simply running a cmdlet and get a new certificate, there is a procedure to do it. Check the following steps:
1. Run Get-ExchangeCertificate |FL – This will list details of all certificates that you have assigned to Exchange Services. Please understand, this cmdlet does not retrieve any information about any other certificate from local certificate store which is not used by Exchange. Once you get the output printed on the screen; note down the Thumbprint of certificate into a notepad.
2. Run Get-ExchangeCertificate –Thumbprint “58C846DEEA2865CA9E6DD4B42329A9AC994EBF63” | New-ExchangeCertificate . This renews the certificate. You will notice the moment you press enter on keyboard you may be prompted to confirm if you want to use the same certificate for SMTP service.

3. Check if the certificate is renewed. This can be simply examined by looking at the changes in thumbprint of the certificate after running the cmdlet mentioned in step 2. You can see the changed thumbprint in below picture.

4. Looking correctly to the above picture you will also notice that the certificate is not being used to secure IIS based services anymore though the NotAfter and NotBefore dates have changed. To enable this renewed certificate for IIS as well run Enable-ExchangeCertificate – Thumbprint “E0BB201793DC74D0F94F3275E6AA53BA75907565” –Services IIS
5. Verify all the services are working correctly after renewing and enabling the certificate.
6. Remove old certificate by running Remove-ExchangeCertificate –Thumbprint “58C846DEEA2865CA9E6DD4B42329A9AC994EBF63”

Comments

Post a Comment

Popular posts from this blog

Calculate how much data can be transferred in 24 hours based on link speed in data center

  In case you are planning for migration via DIA or IPVPN link and as example you have 200Mb stable speed so you could calculate using the below formula. (( 200Mb /8)x60x60x24) /1024/1024 = 2TB /per day In case you have different speed you could replace the 200Mb by any rate to calculate as example below. (( 5 00Mb /8)x60x60x24) /1024/1024 =  5.15TB  /per day So approximate each 100Mb would allow around 1TB per day.
Post a Comment
Read more

Recreating a VMFS-3 or VMFS-5 partition table in ESXi 5.x

For this kind of issues you need to engage VMware support on this, following any part of this article could lead to more complex situation if not ran by an expert.   Symptoms Datastore does not mount because of a lost or overwritten partition table.   Purpose When a VMFS partition is created in ESX 3.x or ESX 4.x, it has a Master Boot Record (MBR) partition map. The MBR is written to the first 512 B block (LBA0) and contains the information where the (VMFS) partition starts and ends. ESXi 5.0 introduced VMFS-5, which uses a GUID partition table (GPT) for new datastores. When a VMFS-3 partition is created in ESXi 5.x and is later updated to VMFS-5, the original partition map (MBR) is maintained. If the partition information of a VMFS datastore is deleted or overwritten (for example, by a Windows system with direct access to the same disks), it is impossible to determine if the partition map was GPT or MBR. The only time you can be sure that a GPT partition map was used is if th...
Post a Comment
Read more

How to deploy an OVA in Cloud Director

  How to deploy an OVA in Cloud Director Yesterday I was in a call with a customer and we discussed uploading OVA’s into Cloud Director. I said sure that is no problem at all. Well then I started thinking how are you supposed to deploy an OVA in Cloud Director because I do not even remember how this is done. So I opened up Cloud Director and tried it for myself. I decided to make this blog post along the way to show you how to deploy an OVA in Cloud Director. As an added bonus I will also show you how to upload an OVA to the catalog. This way I can deploy the OVA over and over again. Environment information Cloud director 10.3 OVA How to deploy an OVA in Cloud Director In Cloud director I opened up the Applications section and selected “NEW” I am deploying an OVA so I selected “Add vApp From OVF”. In the screenshot below you can see all the steps involved with (in my case) deploying and customising the Usagemeter. Options to customise are for instance: Network settings, vApp naming...
Post a Comment
Read more