Skip to main content

How to Turn Off the Outlook 2010 Social Connector

 Outlook 2010 features a new Outlook Social Connector that integrates Outlook with several social networking sites, such as Facebook, Twitter and My Space. The idea is to provide a pane at the bottom of each message that shows the recent social networking updates from the senders and recipients in each message. Outlook 2010 will also pull photos or avatars of the senders and recipients from these social networks to provide a fuller, richer and more personal messaging experience.







For more information about the Outlook Social Connector, see Announcing the Outlook Social Connector on the Outlook product team's blog.

While this might be a good idea for home users or businesses that are more open to social networking, I find that most corporate networks block access to social networking sites like Facebook, Twitter, and My Space. This renders the Outlook Social Connector useless and takes up valuable screen real estate, as shown below.


If you happen to click the "People Pane" (highlighted in red above) it expands to show more information from the configured social networking sites, taking up even more room. Here's how to get rid of it.

On the Outlook 2010 main screen click the View tab, then People Pane, then select Off. Viola!

Comments

Post a Comment

Popular posts from this blog

Calculate how much data can be transferred in 24 hours based on link speed in data center

  In case you are planning for migration via DIA or IPVPN link and as example you have 200Mb stable speed so you could calculate using the below formula. (( 200Mb /8)x60x60x24) /1024/1024 = 2TB /per day In case you have different speed you could replace the 200Mb by any rate to calculate as example below. (( 5 00Mb /8)x60x60x24) /1024/1024 =  5.15TB  /per day So approximate each 100Mb would allow around 1TB per day.
Post a Comment
Read more

Recreating a VMFS-3 or VMFS-5 partition table in ESXi 5.x

For this kind of issues you need to engage VMware support on this, following any part of this article could lead to more complex situation if not ran by an expert.   Symptoms Datastore does not mount because of a lost or overwritten partition table.   Purpose When a VMFS partition is created in ESX 3.x or ESX 4.x, it has a Master Boot Record (MBR) partition map. The MBR is written to the first 512 B block (LBA0) and contains the information where the (VMFS) partition starts and ends. ESXi 5.0 introduced VMFS-5, which uses a GUID partition table (GPT) for new datastores. When a VMFS-3 partition is created in ESXi 5.x and is later updated to VMFS-5, the original partition map (MBR) is maintained. If the partition information of a VMFS datastore is deleted or overwritten (for example, by a Windows system with direct access to the same disks), it is impossible to determine if the partition map was GPT or MBR. The only time you can be sure that a GPT partition map was used is if th...
Post a Comment
Read more

How to deploy an OVA in Cloud Director

  How to deploy an OVA in Cloud Director Yesterday I was in a call with a customer and we discussed uploading OVA’s into Cloud Director. I said sure that is no problem at all. Well then I started thinking how are you supposed to deploy an OVA in Cloud Director because I do not even remember how this is done. So I opened up Cloud Director and tried it for myself. I decided to make this blog post along the way to show you how to deploy an OVA in Cloud Director. As an added bonus I will also show you how to upload an OVA to the catalog. This way I can deploy the OVA over and over again. Environment information Cloud director 10.3 OVA How to deploy an OVA in Cloud Director In Cloud director I opened up the Applications section and selected “NEW” I am deploying an OVA so I selected “Add vApp From OVF”. In the screenshot below you can see all the steps involved with (in my case) deploying and customising the Usagemeter. Options to customise are for instance: Network settings, vApp naming...
Post a Comment
Read more